Adipic Acid SDS MSDS of Manufacturers & Exporters
Please visit Adipic Acid USP NF ACS BP Ph Eur EP JP IP Analytical reagent FCC Food grade Manufacturers our associates world class FDA-GMP approved, ISO-9001 Certified facility Anmol Chemicals
Adipic Acid CAS Number 124-04-9
Adipic Acid SDS, Safety Data Sheet
MSDS, Material Safety Data Sheet 14-Aug-22
SECTION 1. PRODUCT IDENTIFICATION
Product Name & Other Names: Adipic Acid or Hexanedioic acid.
CAS Number: 124-04-9
EINECS EC Number: 204-673-3
Molecular Formula: C6H10O4
Molecular Weight: 146.14
Relevant uses and uses advised against (if any): Industrial Manufacturing.
Supplier: As per the letterhead.
SECTION 2. HAZARDS IDENTIFICATION
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008
Serious eye damage (Category 1)
Labeling according to GHS USA & Regulation (EC) No 1272/2008
GHS Label Elements
Corrosive |
Signal Words: Danger
Hazard statements:
H318: Causes serious eye damage.
Precautionary statements:
P261: Avoid breathing dust/ fume/ gas/ mist/ vapors/ spray.
P262: Do not get in eyes, on skin, or on clothing.
P264 Wash skin thoroughly after handling.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
SECTION 3. COMPOSITION / INFORMATION ON INGREDIENTS
Product Name & Other Names: Adipic Acid or Hexanedioic acid.
CAS Number: 124-04-9
EINECS EC Number: 204-673-3
SECTION 4. FIRST AID MEASURES
Always seek medical attention after first aid measures are provided.
Eye Contact: Do not allow victim to rub eye (s). Let the eye (s) water naturally for a few minutes. If particle/dust does not dislodge, flush with lukewarm, gently flowing water for 5 minutes or until particle/dust is removed, while holding eyelid (s) open. If irritation persists, obtain medical attention. DO NOT attempt to manually remove anything stuck to the eye.
Skin Contact: Remove contaminated clothing, shoes, and leather goods (e.g. watchbands, belts). Quickly and gently blot or brush away excess chemical. Wash gently and thoroughly with lukewarm gently flowing water and non-abrasive soap for 5 minutes. If irritation persists, repeat flushing. Obtain medical advice. Completely decontaminate clothing, shoes and leather goods before reuse or else discard.
Inhalation: If symptoms are experienced, remove source of contamination or move victim to fresh air. Obtain medical advice.
Ingestion: Never give anything by mouth if victim is rapidly losing consciousness or is unconscious or convulsing. Have victim rinse mouth thoroughly with water. DO NOT INDUCE VOMITING.
SECTION 5. FIRE FIGHTING MEASURES
Fire and Explosion Hazards: Not considered flammable but may burn at high temperatures. Airborne dusts of this product in an enclosed space and in the presence of an ignition source may constitute an explosion hazard.
Extinguishing Media: Use means of extinction appropriate for the surrounding fire conditions such as water spray, carbon dioxide, dry chemical, or foam.
Fire Fighting: Apart from oxides of carbon. toxic fumes may result from combustion. As with any fire, fire fighters should be fully trained and wear full protective clothing including an approved, self-contained breathing apparatus which supplies a positive air pressure within a full-face piece mask. Use water spray to cool unopened containers.
SECTION 6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment, and emergency procedures: Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.). Restrict unprotected personnel from the area. Do not approach facing the wind. Close-fitting safety goggles may be necessary in some circumstances to prevent eye contact.
Environmental precautions: Do not let the product enter drains, soil or water sources.
Methods and materials used for containment Cleanup procedures and Storage: Contain spilled material. Contain spill, isolate hazard area, and deny entry. Sweep up or vacuum. Place contaminated material in suitable, labeled containers for final disposal. Dispose of waste material consistent with the requirements of waste disposal authorities.
SECTION 7. HANDLING AND STORAGE
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices. Ensure proper ventilation. Wash thoroughly after handling. Do not drink, eat, or smoke while handling. Avoid contact with skin, eyes, and clothing. Minimize dust generation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Avoid contact with eyes, skin, and clothing. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Conditions for safe storage, including any incompatibilities: Store in cool, dry, and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Do not leave the material container open. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid contact with skin and eyes. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like oxidizing agents, strong reducing agents, and bases. Keep away from sources of ignition. Take measures to prevent the build-up of electrostatic charge. It is good practice to keep container closed when not in use. May form combustible dust concentrations in air.
SECTION 8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Exposure limit(s): Contains no substances with occupational exposure limit values in some countries. Better go by 5 mg/m3 TLV ACGIH.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible.
Personal Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator may be worn.
Skin Protection: Wear protective gloves and clean body-covering clothing.
Eye Protection: Use chemical safety goggles and/or full face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Handle in accordance with good industrial hygiene and safety practice. Wash hands after handling.
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: It is a white, odorless granules crystals or powder
Odor: None
Odor threshold: Not available.
pH: 2.5 to 4
Relative density: 1.36
Freezing/Melting Point/Range: 151C to 154C
Boiling Point: Decomposes at 337C
Flash point: Not available.
Auto-ignition temperature: No information found.
Decomposition temperature: No information found.
Upper/lower flammability or explosive limits: No information found.
Vapor pressure: No information found.
Vapor density: No information found.
Evaporation rate: No information found.
Flammability (solid, gas): No information found.
Partition coefficient: n-octanol/water: No information found.
Solubility in Water: Soluble in water.
Viscosity: No information found.
Molecular Formula: C6H10O4
Molecular Weight: 146.14
SECTION 10. STABILITY AND REACTIVITY
Stability and Reactivity: Stable and not considered reactive under normal temperatures and pressures. Hazardous polymerization or runaway reactions will not occur.
Incompatibilities: Oxidizing agents. Avoid excessive heat, spark, flame, ignition dust formation and electrical charging. Also avoid strong reducing agents and bases.
Hazardous Decomposition Products: High temperature will generate carbon oxide and fumes.
SECTION 11. TOXICOLOGICAL INFORMATION
Acute Toxicity:
LD50 Oral - Rat - male and female - 5,560 mg/kg
LC0 Inhalation - Rat - male and female - 4 h - > 7.7 mg/l
LD0 Dermal - Rabbit - male and female - 7,940 mg/kg
Carcinogenicity: IARC: No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC.
Reproductive toxicity: No information found.
Teratogenicity: No information found.
Mutagenicity: No information found.
SECTION 12. ECOLOGICAL INFORMATION
Toxicological data:
Toxicity to fish: static test LC0 - Brachydanio rerio (zebrafish) - >= 1,000 mg/l - 96 h.
Toxicity to daphnia and other aquatic invertebrates: Immobilization LC50 - Daphnia magna (Water flea) - 46 mg/l - 48 h.
Results of PBT and vPvB assessment: This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.
SECTION 13. DISPOSAL CONSIDERATIONS
Do not wash the material down drain. Put uncontaminated material back into the process if possible. Place contaminated material in suitable, labeled containers for disposal.
SECTION 14. TRANSPORT INFORMATION
DOT USA & ADR/RID Europe: Not controlled.
IATA/ICAO & IMO/IMDG: Not controlled.
SECTION 15. REGULATORY INFORMATION
USA Regulations:
SARA 311/312 Hazards: Acute Health Hazard.
California Prop. 65 Components: Not listed.
SECTION 16 - ADDITIONAL INFORMATION
Disclaimer:
**************************
Our company provides this MSDS sheet in good faith but makes no representation as to its comprehensiveness or accuracy. This SDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. The above information has been compiled from various sources and has the possibility of discrepancy and being out-dated information. Individuals receiving the information must exercise their independent judgment and do further search in determining its appropriateness for a particular purpose. In no case shall our company be liable to loss or damages by the product user.
**************************
Specifications of Adipic Acid BP Ph Eur EP JP USP NF IP ACS Analytical Reagent FCC Food grade Manufacturers |
